Work from the bench, the field, and everywhere in between.

A large parking lot calls for more than a wide-angle view.

A high-rise camera installation overlooking a large parking lot, with optical zoom to bring distant areas into view.

• General

Under the Microscope: A Flash Drive Board, Repaired by Hand

• data-recovery

On the Bench: The Oscilloscope

• Repairs

Main Level Run, Down Into the Basement

• networking

Rough-In Done Right, Ready for Drywall

• networking

One Rack Runs the Whole House

• networking

NVMe Liquid Damage: Mapping Corrosion Under the Microscope

• General

Door Sensor and Security Panel Wiring in Madison AL

Finishing up wiring in door sensors and monitoring panels.

• On-Site

Custom Gaming Computer Build in Madison AL

We build custom gaming PCs in Madison, AL. You pick the parts or we spec the whole thing for you. Doesn't matter if you want a budget 1080p machine or a 4K monster. Every build gets burn-in tested and a full QC pass before it leaves our shop. Then it's covered by a local warranty. Something goes wrong? You bring it to us. Not a shipping label. Not a call center. Us. Right here in Madison. We serve gamers across Huntsville and North Alabama. If you're thinking about a custom build, come talk to us first. We'll spec it right and build it right.

• Repairs

Business Access Control Installation in Madison AL

Need to control who gets in your building? We install access control systems for businesses in Madison and Huntsville AL. Keypads, card readers, door controllers. We wire it, configure it, and make sure it works with your existing setup. No more rekeying locks when someone leaves. You manage it all from your desk. ProTek handles the full install. We run the cable, mount the hardware, program the system, and show your team how to use it. If your business needs better door security in the Madison or Huntsville area, talk to us. We do this right the first time. Every door gets tested. Every credential gets verified. You get a system you can trust.

Xbox Series X HDMI Port Replacement in Madison AL

Xbox Series X with no video? It's the HDMI port. The pins inside bend when the cable gets yanked or the console gets moved while plugged in. We replace Xbox Series X HDMI ports in our Madison, AL shop. It's micro-soldering under the microscope. Pull the bad port, clean the pads, solder on a new one, test it. We keep the ports in stock so you're not waiting weeks or shipping your console across the country. If you're in Huntsville or Madison and your Xbox won't show a picture, bring it by. Most of these go out in a day or two. We'll get you back gaming.

• micro-soldering

Xbox HDMI Port Repair in Madison AL

Your Xbox has no signal on the TV. The HDMI port is probably damaged. We replace Xbox HDMI ports in our Madison, AL shop. We keep ports in stock for Xbox Series X, Series S, and One, so most of these turn around fast. Micro-soldering work, done right. Serving Madison, Huntsville, and North Alabama.

• micro-soldering

Whole Home Audio Installation in Madison AL

Whole-home audio, finished and sounding great. Music in the kitchen, something different on the patio. Each area is controlled separately so everyone can enjoy their own music.

• residential

Network Rack Installation in Madison AL

A real estate company called and asked if we could install a two-post network rack. Yep. Their IT team handled the equipment. We handled the part that needed drilling into concrete and making sure the rack was not going anywhere. Mounted, anchored, and ready for their team.

• business-it

Network Cable Testing in Madison AL: Every Run, Every Time

Remember all that cable we pulled? Now we test every single run. Terminate it. Test it. Pass. Then it is ready for drywall. No run gets buried until i

• networking

Outdoor Live Stream Setup in Madison AL

A&M University needed to live stream their outdoor tennis matches, and we made it happen. Outdoor pole-mounted enclosure with a wireless bridge, built

• business-it

Swollen MacBook Battery Replacement in Madison AL

Is your MacBook trackpad popping up? Case not sitting flat? That's a swollen battery. It's not just annoying. It's a safety issue. Lithium batteries swell when they fail, and a swollen one can be dangerous. Stop charging it. We replace swollen MacBook batteries in our Madison, AL shop. Most of the time it's same-day. We open it up, remove the bad battery safely, install a new one, and test everything. If you're in Madison or Huntsville and your MacBook battery is swelling, bring it in now. Don't put it off. And definitely don't poke it. Seriously. Bring it in. We'll take care of it.

• computer-repair

Retrofit Network Cable Installation in Huntsville AL

Sheetrock went up before the holes were drilled. The wiring was already in place, so getting it through the door frames was the interesting part. Ready

• networking

PS5 HDMI Port Replacement in Madison AL

PS5 turns on but no picture? It's the HDMI port. Happens all the time. Cable gets yanked, console gets bumped while it's plugged in, pins bend. We fix these in our Madison, AL shop. It's micro-soldering work under the microscope. We pull the bad port, clean up the pads, solder on a new one, test it on a display. We keep PS5 HDMI ports in stock so most of these go out in a day or two. You don't have to ship your console off and wait weeks. If you're in Huntsville or Madison and your PlayStation 5 won't show video, bring it by. We'll get you fixed up.

• micro-soldering

PS5 Board Component Repair in Madison AL

PS5 won't power on? Or keeps shutting off? It's not always the HDMI port. Sometimes a component on the board blows. A capacitor. A power IC. Something small that kills the whole console. Finding it takes a microscope, a micro-soldering station, and knowing how these boards work. We do PS5 board-level repair in our Madison, AL shop. We trace the fault, replace the bad component, and test everything before it goes back. If your PlayStation 5 is dead and you're in Huntsville or Madison, bring it to ProTek. Most shops will tell you to buy a new one. We'd rather fix yours.

• micro-soldering

Security Camera Installation in Madison AL

Security cameras for your entire property, inside or out. We install camera systems for homes, businesses, new construction, offices, shops, and wareh

• security

Network Cabinet Cleanup in Huntsville AL: Before and After

Sometimes you do not get to start with a clean slate. We came into this cabinet with existing equipment and a mess of cabling. Instead of replacing ever

• networking

Micro-Soldering Board Repair in Madison AL

Micro-soldering looks simple from across the room. It's anything but. We're talking components smaller than a grain of rice. HDMI ports. Charging ports. Blown chips. All of it done under the microscope with a steady hand. We do board-level micro-soldering in our Madison, AL shop every day. If another shop told you it can't be fixed, bring it to us. Half our work is fixing what someone else gave up on. We serve Madison, Huntsville, and North Alabama. Phones, consoles, laptops, tablets. If it's got a board and it's broken, we'll take a look. That's the job. That's what we do.

• micro-soldering

Liquid Damage Repair in Madison AL

Spilled coffee on your laptop? Don't turn it on. Don't try to dry it with a hair dryer. Bring it to us. Liquid damage is a race against the clock. Corrosion starts the second it dries. We do liquid damage repair in our Madison, AL shop. The board goes under the microscope. We map every affected spot, clean it with ultrasonic equipment, and micro-solder what's damaged. The sooner you bring it in, the better your odds. If you're in Huntsville or Madison and something got wet, power it down and bring it to ProTek. Don't wait. Waiting is what kills it.

• micro-soldering

Hotel WiFi Installation and Troubleshooting in Huntsville AL

Getting Wi-Fi working is one thing. Making it work across an entire hotel is another. This hotel already had equipment installed but was having issues

• business-it

GPU Board Repair in Madison AL

Graphics card acting up? Artifacts on screen? Not detected? These cards cost too much to throw away. We repair GPUs at the board level in our Madison, AL shop. Heat the board, lift the damaged component, install the replacement, test it under load. It's the same micro-soldering work we do on consoles and laptops. If you're in Huntsville or Madison and your GPU is failing, bring it to ProTek before you buy a new one. A board repair costs a fraction of a new card. And we'd rather fix what you have than watch you overspend. Most shops won't touch board-level GPU work. We do it every week.

• micro-soldering

Fluke LinkIQ Repair in Madison AL

A $2,000 Fluke LinkIQ with a busted Ethernet jack. Most people would toss it and buy a new one. We didn't. We replaced the jack in our Madison, AL shop and put it back to work. That's what we do. We fix the expensive stuff. Test equipment. Pro gear. The things that cost too much to replace on a whim. If you're in Madison or Huntsville with equipment someone said isn't worth repairing, let us take a look. You might be surprised. We'd rather fix it than watch you buy a new one. That's the whole point of a repair shop.

• micro-soldering

Elevator Emergency Phone Wiring in Huntsville AL

Not your typical Ethernet run. This one went to the elevator for its VoIP emergency phone on a new construction project. Protected in liquid-tight con

• networking

Doorbell Camera Installation in Madison AL

Another entry and doorbell camera on a new construction home. Mounted clean on the brick next to the front door, wired in while the walls were still op

• residential

Dental Operatory Monitor Installation in Huntsville AL

One from the archives. We installed an operatory monitor for one of our local dental clients. From installs like this to complete office moves and new

• business-it

Dental Office IT Setup in Madison AL

Another new dental office wrapped up and ready for business. We handled the technology through the entire build: Wi-Fi, wired networking, security cam

• business-it

CPU Socket Pin Assessment in Madison AL

Broken pins in a CPU socket. Not bent. Broken. That's a harder conversation. Sometimes we can work around it. Sometimes the board is done. We won't guess. We put it under the microscope in our Madison, AL shop, map every damaged pin, and tell you straight whether it's worth saving. That's the assessment. Honest. No charge for telling you the truth. If you're in Madison or Huntsville with a damaged socket, bring it to ProTek. We'll look at it and give you a real answer. Not a shrug. A real answer. That's what we're here for. Even if the answer is no, you'll know for sure.

• micro-soldering

Corrosion Damage Repair in Madison AL

The spill dried weeks ago. The damage is still spreading. Corrosion doesn't stop when the liquid evaporates. It keeps eating traces and weakening solder joints. Then one day the device just dies. We repair corrosion damage in our Madison, AL shop. Under magnification we find every compromised trace, clean it properly, and rebuild what's lost. If your device got wet a while back and now it's acting strange, that's probably why. Bring it to ProTek in Madison. We serve Huntsville and North Alabama. The longer you wait, the worse it gets. But we've saved boards that looked hopeless. Bring it in and let us look.

• micro-soldering

Running Network Cable Through Concrete in Madison AL

Pulling CAT6 Ethernet cable. One, bore through the concrete wall. Two, open up the double fire barrier. Three, find the cable you fished through. Fou

• networking

Church WiFi Installation in Madison AL: Full Building Coverage

Blanketing a two-story church in Wi-Fi takes more than a few access points. We designed and installed coverage through the sanctuary, offices, common

• business-it

CAT6 Wiring and WiFi Install in Huntsville AL

High ceilings meant the scissor lift came out for this one. We ran CAT6 drops across the space and mounted access points where the coverage map said they'd do the most good. When you're working twenty feet up, you measure twice and pull once — there's no quick trip back up for a forgotten cable.

• networking

Business Internet Upgrade in Madison AL: Ditching Comcast for Fiber

Comcast was not cutting it. Slow speeds, constant issues. We ripped it out and put in a proper business internet setup. New cabinet, new equipment, waiting on the fiber to light up. This is what we do for businesses in Madison and Huntsville AL. Your internet is the backbone of everything. If it is slow or unreliable, your whole team suffers. We assess what you need, install the right gear, and make sure it is configured properly. Router, firewall, switches, WiFi. All of it. If your business internet is holding you back, call ProTek. We will get you on something that actually works.

• business-it

Commercial Network Wiring in Huntsville AL

When a business needs the wiring done, we get it done. Data drops throughout the building, HDMI connections ready for laptops, and cabling in place for

• networking

Bent CPU Pin Repair in Madison AL

Bent pins in the CPU socket? It happens more than you'd think. CPU cooler gets pulled off wrong. Chip gets dropped in crooked. Suddenly the board won't boot. We straighten bent CPU pins under magnification in our Madison, AL shop. It's slow, careful work. One pin at a time. We saved this board when it looked like a lost cause. If you're in Huntsville or Madison and your socket is damaged, bring it to ProTek before you buy a new motherboard. Sometimes it's an easy save. Sometimes it's not. We'll tell you straight which one it is. That's free to find out.

• micro-soldering

Commercial Ethernet Wiring in Madison AL: 53 Drops, One Building

Fifty three Ethernet drops in one building. The last one always makes you nervous. You pull all that cable and every run has to test clean. We do commercial Ethernet wiring for businesses in Madison and Huntsville AL. New construction, existing buildings, it does not matter. We run the cable, terminate it, test every single run, and label everything. Your IT guy will thank us. A wired connection beats WiFi every time for speed and reliability. If your office needs network drops, new or additional, call ProTek. We have pulled thousands of runs across North Alabama. We show up, we do it right, and every cable gets tested before we leave.

• networking

Long Distance Network Cable Runs in Madison AL

Need network cable run? Some runs are simple. Some are 300+ feet. Before the drywall goes up is easier. After it goes up, we do that too. One cable or

• networking

Network Cabinet and Security Camera Install in Madison AL

This network cabinet was built out to support a full camera system — 24 ports of switching, PoE for every camera, and clean cable management from day one. When the infrastructure is done right the first time, adding cameras later is just plug and play.

• business-it

Business WiFi Installation in Madison AL: 14 Access Points, Two Switches

This business needed WiFi that actually works everywhere. Fourteen access points and two switches. No room for a rack mount, so we made it work with what we had. That is what we do. Business WiFi in Madison and Huntsville AL is not about throwing a router in the corner. It is about planning coverage, running the cable right, and mounting hardware where it belongs. We handle the full job. Cable runs, switch config, access point placement, testing every drop. If your office WiFi has dead spots or your team complains about slow connections, we fix that. ProTek does business networking for companies across Madison, Huntsville, and North Alabama. One call and your network just works.

• networking

Platter Scoring Data Recovery in Madison AL

You can only see this damage under green light. Rotational scoring. A failed head kept spinning against the platter and scored the surface in circles. We see this in our Madison, AL cleanroom more than we'd like. Every scored drive gets assessed before we promise anything. Sometimes we can image around the scoring and get most of the data. Sometimes the damage is too deep. Either way, you get a straight answer from us. Not a maybe. Not a sales pitch. If your drive is clicking or grinding, power it down and bring it to ProTek. We handle scored platter recovery for Madison, Huntsville, and all of North Alabama. The sooner you bring it in, the better your odds.

• Data Recovery
• Huntsville, AL

Scored Platter Data Recovery in Madison AL

That ring isn't a reflection. It's carved into the platter. A failed head dragged across the surface and engraved a ring into it. That part of the platter is gone forever. But the rest might still read. We imaged around the damaged area in our Madison, AL lab and recovered what survived. Then we told the customer exactly what made it and what didn't. That's how we do data recovery. Straight answers. No fairy tales about 100% recovery when the platter looks like this. If your drive is making noise or acting strange, stop using it and bring it to ProTek. We serve Madison, Huntsville, and North Alabama. We'll assess it honestly and tell you what's possible before you spend a dime.

• Data Recovery
• Huntsville, AL

Dead SSD Data Recovery in Madison AL

This PNY SSD was completely dead. Wouldn't show up anywhere. So we forced it into safe mode. Soldered a jumper, got the drive talking, then used PC-3000 to rebuild the translator and recover the data. That's the kind of recovery most shops won't touch. It takes micro-soldering and flash tools most places don't have. We do dead SSD recovery in our Madison, AL lab for Huntsville and North Alabama. If your SSD died and someone told you it's unrecoverable, get a second opinion from us. We've pulled data off drives that looked completely gone. Bring it in. We'll tell you the truth about what we can do.

• Data Recovery
• Huntsville, AL

Hard Drive Damage Assessment in Madison AL

We had to tell this customer no. The platters were covered in magnetic dust. The data was gone. Not mostly gone. Gone. We'd rather turn down a job than take your money for a recovery that can't happen. That's the deal at ProTek. If we can save your data, we will. If we can't, we'll tell you straight and we won't charge you for trying the impossible. Most shops won't say that out loud. We will. Our Madison, AL lab handles the hard cases for Huntsville and North Alabama. Clicking drives, dead drives, drives other shops gave up on. Bring it in and we'll give you an honest assessment. That's free. And if we say we can do it, we mean it.

• Data Recovery
• Huntsville, AL

iMac Data Recovery in Madison AL

iMac won't boot and you need the files? We can get them. We got this one working again long enough to pull the data in our Madison, AL lab. iMacs are glued shut. Opening one without cracking the screen takes the right tools and a careful hand. We've done it hundreds of times. If your iMac or Mac died and the data matters, bring it to ProTek in Madison. We serve Huntsville and North Alabama for Mac data recovery. Photos, documents, whatever you had on there. Don't assume it's gone. Let us take a look first. That's what we're here for. Most of the time, we get it all.

• Data Recovery
• Huntsville, AL

Hard Drive Head Replacement in Madison AL

The head came clean off the slider arm. That's about as bad as a mechanical failure gets. The part that reads your data broke loose inside the drive. We found a matching donor, moved the head stack over in our cleanroom, and got the data back. Work like this is why we have a cleanroom in Madison, AL in the first place. Most shops in Alabama don't do head transplants. They'll tell you it's unrecoverable. We've been doing them for years. If your drive made a terrible noise and then died, and someone already told you it's hopeless, bring it to us. We serve Madison, Huntsville, and all of North Alabama. Worst case, we tell you the truth for free. Best case, you get your files back.

• Data Recovery
• Huntsville, AL

Broken USB Drive Data Recovery in Madison AL

USB connector barely hanging on? We see this constantly. The connector gets loose, people keep wiggling it, and one day it snaps off. We got a temporary connector on this one long enough to pull the data, then repaired it properly. That's the kind of work we do in Madison, AL. If your flash drive connector is loose or damaged, bring it to us before it breaks off completely. Every wiggle makes it worse. We serve Madison, Huntsville, and North Alabama. Don't wait until it's too late. Bring it in now. We'll get your files back and fix the drive right.

• Data Recovery
• Huntsville, AL

Dead Hard Drive Data Recovery in Madison AL

Head 0 destroyed. That's what killed this drive. When a read/write head fails like that, no software on earth will get your files back. The drive has to be opened. In a cleanroom. By someone who knows what they're doing. We opened this one in our Madison, AL lab, replaced the head assembly with a matched donor, and imaged the platters sector by sector. That's head failure recovery. It's delicate, slow work. One wrong move and the data is gone. We do this for customers across Madison, Huntsville, and North Alabama. If your drive died suddenly and it has stuff you can't lose, don't plug it in again. Don't let a friend tinker with it. Bring it to ProTek. We'll tell you straight whether we can save it.

• Data Recovery
• Huntsville, AL

USB Trace Repair Data Recovery in Madison AL

See that tiny wire? That's a jumper. The trace on this USB board was damaged, so we ran a jumper wire to the good part of the trace and got the data back. Simple work. Steady hands. Microscope. That's USB flash drive recovery in Madison, AL. Not every failure needs a cleanroom. Some just need someone who can see what's broken and fix it at the board level. If your USB drive quit working, bring it to ProTek. We serve Madison, Huntsville, and North Alabama. We'll open it up, find the fault, and tell you straight whether we can save it.

• Data Recovery
• Huntsville, AL

Hard Drive Platter Contamination Recovery in Madison AL

See that smudge? That's a fingerprint. On the platter. Someone opened this drive outside a cleanroom and touched the surface. You can't even see it without a green light. The oil from skin destroys the magnetic layer on contact. We see this more than you'd think. People watch a video online and pop the lid off. Please don't. We decontaminated these platters in our cleanroom in Madison, AL and recovered the data. It worked this time. It doesn't always. If your data matters, bring the drive to ProTek before anyone opens it. Not your buddy. Not a YouTube tutorial. Us. We handle platter contamination recovery for Madison, Huntsville, and North Alabama. And we'll never make it worse trying.

• Data Recovery
• Huntsville, AL

USB Drive PCB Swap Data Recovery in Madison AL

Most USB drive recoveries go better once we move the drive to a SATA interface.

• Data Recovery
• Huntsville, AL

Clicking Hard Drive Data Recovery in Madison AL

Drive started clicking? Stop using it. Right now. That clicking sound is the read/write heads failing. Every second it spins, the heads can scrape the platters and destroy your data for good. This one came in clicking and wouldn't mount. We opened it in our cleanroom in Madison, AL, swapped the head stack with a matching donor, and got 90% of the files back. That's what clicking hard drive recovery takes. Special tools, a dust-free room, and knowing exactly which donor drive will work. Most shops can't do this. We do it every week. If you're in Madison or Huntsville and your drive is clicking, power it down and bring it in. Don't run software on it. Don't freeze it. Just bring it to us.

• Data Recovery
• Huntsville, AL

USB Circuit Board Data Recovery in Madison AL

Your USB drive quit and it's not the connector? Then it's the tiny board inside. That's where the real work happens. The controller, the memory, the traces connecting them. When any of that fails, the drive goes silent. We work at the board level in our Madison, AL lab. Micro-soldering under the microscope. If your flash drive stopped working and another shop said it's dead, bring it to ProTek in Madison. We serve Huntsville and North Alabama. Dead doesn't always mean dead. Sometimes it just means nobody looked close enough. Bring it in. We'll take a look. No charge for the honest answer.

• Data Recovery
• Huntsville, AL

USB Connector Board Repair in Madison AL

The USB connector ripped off and took the board traces with it. That's two problems, not one. We repaired both in our Madison, AL shop. New connector soldered on. Traces rebuilt under the microscope. Then we tested it to make sure it actually works. If your USB drive or device has a broken connector, bring it to ProTek in Madison. Don't keep wiggling it hoping it'll connect. You'll tear up the board worse. We serve Huntsville and North Alabama. Board-level USB repair is what we do. Bring it in before it gets worse. We'll take a look and tell you straight what it'll take.

• Data Recovery
• Huntsville, AL

Surface Data Recovery in Madison AL

This Microsoft Surface came in with liquid damage and a badly broken screen.

• Data Recovery
• Huntsville, AL

Circuit Board Data Recovery in Madison AL: Six Bad Capacitors

This recovery came down to the logic board. Six capacitors had failed — swollen, leaking, done. We replaced all six, verified the board was stable, and got the full data recovery. Sometimes it's not the drive that fails, it's the board around it.

• Data Recovery
• Huntsville, AL

Seagate Firmware Data Recovery in Madison AL

This Seagate wouldn't mount. The heads were fine. The platters were fine. The firmware was corrupted and the drive locked itself out. That's a software problem inside the drive's own brain. Fixing it takes PC-3000 and someone who knows how to use it. Most shops don't have either. We rebuilt the firmware in our Madison, AL lab and got 99% of the data back. That's Seagate firmware recovery. It's not something you can download a tool for. If your Seagate or any drive suddenly stopped showing up and the data matters, bring it to ProTek. Don't keep plugging it in hoping it'll come back. It won't. We serve Madison, Huntsville, and North Alabama for firmware-level recovery. Bring it in and we'll take a look.

• Data Recovery
• Huntsville, AL

SD Card Data Recovery in Madison AL

Yeah, this SD card ended up in someone's mouth. It stopped working. We fixed the physical damage and got all the data back. SD cards hold the stuff you can't reshoot. Wedding photos. Work files. That video of your kid. When one dies, it feels like a disaster. It's usually fixable. We do SD card data recovery in our Madison, AL lab for Huntsville and North Alabama. Bent, snapped, chewed, corroded. We've seen it all. Strange damage doesn't scare us. If your SD card quit and the files matter, bring it to ProTek. Don't try to bend it back yourself. You'll make it worse. Let us handle it.

• Data Recovery
• Huntsville, AL

USB Board-Level Data Recovery in Madison AL

Sometimes the drive won't even talk to the computer. The USB port looks fine. The problem is deeper. The controller or the board itself failed. For this one we had to work past the dead USB interface before we could read a single sector. That's board-level USB recovery. It takes micro-soldering and knowing how these drives are built. Most data recovery shops don't do board work. We do. In our Madison, AL lab. If your USB drive stopped showing up and another shop said there's nothing they can do, bring it to ProTek. We serve Madison, Huntsville, and North Alabama. There's usually a way in. You just have to know where to look.

• Data Recovery
• Huntsville, AL

Samsung T7 SSD Data Recovery in Madison AL

Samsung T7 quit on you? The memory chips are probably fine. With the T7 it's almost always the bridge board or the firmware. The drive looks dead but the data is sitting right there on the NAND. We work past the failed parts in our Madison, AL lab and get your data back. That's portable SSD recovery. It takes the right adapters and knowing how these drives are built. We do Samsung T7 recovery for Madison, Huntsville, and all of North Alabama. Photos, work files, whatever you had on there. If your T7 or any portable SSD stopped working, don't toss it. Bring it to ProTek. There's a good chance we can get it back.

• Data Recovery
• Huntsville, AL

NVMe SSD Data Recovery in Madison AL

Your NVMe SSD stopped showing up? Don't keep rebooting. That won't help and it can make things worse. NVMe drives don't fail like old hard drives. There's no clicking. No warning. Usually it's the controller or the firmware that quits. The memory chips are probably fine. Getting the data off takes professional flash recovery tools and someone who's done it before. We handle NVMe SSD data recovery in our Madison, AL lab for customers across Huntsville and North Alabama. Dead laptop drive. Dead desktop drive. Drive that vanished after an update. Bring it to ProTek. We'll diagnose it and tell you straight what we can do. No charge for the honest answer.

• Data Recovery
• Madison, AL